Description:
Specifies parameter to configure for evpn leave synch route
Parents: BgpRouterConfig
Children: BgpCustomAttribute
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
JoinedMulticastGroup (JoinedMulticastGroup) |
BGP EVPN Join IPV4 multicast group |
Attribute | Description | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
AggregatorAs |
Aggregator AS Type: string Default: "" (empty string) |
||||||||||||||||
AggregatorIp |
Aggregator IP Type: ip Default: null |
||||||||||||||||
AsPath |
List of AS numbers, in string format, that will be used in the AS_PATH attribute (type code 2) in BGP UPDATE messages. This list identifies the autonomous systems through which the routing information carried in the UPDATE message has passed. Type: string Default: 1 |
||||||||||||||||
AsPathIncrement |
Modifies the AS PATH of each route within a route block. Type: string Default: 1 |
||||||||||||||||
AsPathPerBlockCount |
Number of AS Paths per route block. Type: u32 Default: 1 |
||||||||||||||||
AsPathSegmentType |
Path segment type for the AS path specified by the asPath attribute. Type: enum Default: SEQUENCE Possible Values:
|
||||||||||||||||
AtomicAggregatePresent |
Whether to include the ATOMIC_AGGREGATE attribute in BGP UPDATE messages. When this is TRUE, the receiving BGP speaker cannot de-aggregate the prefix into more specific routes. Type: bool Default: FALSE Possible Values:
|
||||||||||||||||
ClusterIdList |
Identifies the route reflectors that a prefix has passed through. This is the optional CLUSTER_LIST path attribute (type code 10), as covered in RFC 2796. This needs a list of cluster IDs (router IDs). Enter up to four comma-separated cluster IDs in the form of IPv4 addresses. Type: ip Default: 0.0.0.0 |
||||||||||||||||
Community |
List of BGP communities in string format. A community is a group of destinations that share some common property. This is the optional COMMUNITIES community path attribute (type code 8) in UPDATE messages. BGP communities are described in RFC 1997. Type: string Default: 1:1 |
||||||||||||||||
DataPlaneEncap |
Data plane encapsulation Type: enum Default: NONE Possible Values:
|
||||||||||||||||
DistributionType |
VPN parameter distribution type Type: enum Default: ROUND_ROBIN Possible Values:
|
||||||||||||||||
EsImportRouteTarget |
Specify the Ethernet Segment Import Route Target value Type: mac Default: 00:00:00:00:00:00 |
||||||||||||||||
EthernetSegmentId |
Ethernet Segment Identifier Value. Type: string Default: 0 |
||||||||||||||||
EthernetSegmentType |
Ethernet segment type Type: enum Default: TYPE0 Possible Values:
|
||||||||||||||||
EthernetTagId |
Ethernet Tag Identifier Value. Type: u32 Default: 0 |
||||||||||||||||
EviCount |
Number of EVPN instances. Type: u32 Default: 1 |
||||||||||||||||
ExtCommunityEviRouteTarget |
Extended Community EVI Route Target Value Type: string Default: 100:1 |
||||||||||||||||
ExtCommunityEviRouteTargetStep |
Extended Community EVI Route Target(RT) Step Type: string Default: 0:1 |
||||||||||||||||
ExtendedCommunity |
Extended Community Type: string Default: "" (empty string) |
||||||||||||||||
ExtendedCommunityIncrement |
Extended Community Step Type: string Default: "" (empty string) |
||||||||||||||||
ExtendedCommunityPerBlockCount |
Extended Community Per Block Count Type: u32 Default: 1 |
||||||||||||||||
IgmpVersion |
Configures IGMP version Type: enum Default: IGMP_VERSION_2 Possible Values:
|
||||||||||||||||
Ipv6OriginatorId |
IPv6 Originator Id Type: ipv6 Default: null |
||||||||||||||||
LargeCommunity |
List of BGP communities in string format. A large community is a group of destinations that share some common property. This is the optional COMMUNITIES community path attribute (type code 8) in UPDATE messages. BGP large communities are described in RFC 8092. Enter up to eight comma-separated pairs. Put a colon between the parts of the pair. Example: AS:Value,AS:Value,AS:Value. where each AS and Value is between 0 - 4294967295. AS numbers cannot be duplicated. Each AS can have only one value. Type: string Default: 1:1:1 |
||||||||||||||||
LeaveGrpSyncValue |
Specifies leave group synchronization Type: u32 Default: 1 |
||||||||||||||||
LocalPreference |
Value for the LOCAL_PREF path attribute in UPDATE messages. This informs other BGP speakers in the same AS of the local BGP speaker's degree of preference for a route. A higher number means more preference. Type: u32 Default: 10 Range: 0 - 4294967295 |
||||||||||||||||
LocalPreferenceIncrement |
Modifier to allow a routeblock to vary the Local Preference. The count will be tied to Network Count. Type: u32 Default: 0 Range: 0 - 4294967295 |
||||||||||||||||
MaxResponseTime |
Specifies maximum response time Type: u8 Default: 255 |
||||||||||||||||
Med |
Value for the multi-exit discriminator (MED). This is the optional MULTI_EXIT_DISC path attribute (type code 4) in UPDATE messages. This value can be used by a BGP speaker's decision process to discriminate among multiple exit points to a neighboring autonomous system. An exit or entry point with a lower MED should be preferred. Type: u32 Default: null Range: 0 - 4294967295 |
||||||||||||||||
MedIncrement |
Modifier to allow a routeblock to vary the MED. The count will be tied to Network Count. Type: u32 Default: 0 Range: 0 - 4294967295 |
||||||||||||||||
MulticastProtocol |
Configures the Multicast protocol for type 6 and type 7 EVPN routes Type: enum Default: IGMP Possible Values:
|
||||||||||||||||
NextHop |
IP address of the border router that should be used as the next hop to the destinations listed in the UPDATE message. Type: ip Default: null |
||||||||||||||||
NextHopGlobal |
IPv6 address of the border router that should be used as the next hop to the destinations listed in the UPDATE message. Type: ipv6 Default: null |
||||||||||||||||
NextHopLinkLocal |
IPv6 Link Local address for the nexthop Type: ipv6 Default: null |
||||||||||||||||
NextHopType |
NextHopType to identify if Nexthop is a list of ip addresses or single ip address Type: enum Default: IPV4 Possible Values:
|
||||||||||||||||
Origin |
Describes how a prefix came to be routed by BGP. It defines the origin of the path information. This attribute is generated by the AS that originated the route(s) in the update message. Type: enum Default: IGP Possible Values:
|
||||||||||||||||
OriginatingRouterIpv4Addr |
Configures originating router's IPv4 address Type: ip Default: 0.0.0.0 |
||||||||||||||||
OriginatingRouterIpv6Addr |
Configures originating router's IPv6 address Type: ipv6 Default: :: |
||||||||||||||||
OriginatorId |
Router ID of the originator of the route in the local AS. This is the optional ORIGINATOR_ID path attribute (type code 9). Type: ip Default: null |
||||||||||||||||
OriginatorIdType |
Originator Id Type Type: enum Default: IPV4 Possible Values:
|
||||||||||||||||
RouteCategory |
Route Category by default UNDEFINED. Type: enum Default: UNDEFINED Possible Values:
|
||||||||||||||||
RouteDistinguisher |
Route distinguisher (RD) in string format. A route distinguisher is an 8-byte value that is concatenated with an IPv4 prefix to create a unique VPN IPv4 prefix. Type: string Default: 192.0.0.1:1 |
||||||||||||||||
RouteDistinguisherStep |
Increment value for RD for each successive VRF within a routeblock. Type: string Default: 0:1 |
||||||||||||||||
RouteTarget |
Value of the extended community path attribute called Route Target, in string format. This is the Route Target extended community, carried in the optional Extended Community path attribute (type code 16) in UPDATE messages. The Route Target identifies a set of sites to which a PE router distributes routes. BGP extended communities are described in an Internet Draft. Type: string Default: 100:1 |
||||||||||||||||
RouteTargetStep |
Increment value for RT for each successive VRF within a routeblock. Type: string Default: 0:1 |
||||||||||||||||
SessionIpVersion |
BGP route's session IP version. Type: enum Default: IPV4V6 Possible Values:
|
||||||||||||||||
SourceFilterMode |
Configures source filter mode -Include Group Type or Exclude Group Type Type: enum Default: INCLUDE Possible Values:
|
||||||||||||||||
SourceIpv4Addr |
Configures source IPv4 address to be used for source filter mode- Include Group Type Type: ip Default: 192.0.1.0 |
||||||||||||||||
SourceIpv4AddrStep |
Configures source IPv4 address step. Type: ip Default: 0.0.0.1 |
||||||||||||||||
SrcCount |
Configures source IPv4 address count. Type: u8 Default: 1 Range: 1 - 255 |
There are no read-only attributes.