Description:
Used in the end of test result database. You cannot subscribe to this object to get results.
Parents: Project
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
ResultParent (ResultChild) |
Use this to connect a results object to an object. |
Attribute | Description | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
Read-Only Attribute | Description |
---|---|
AvgJitter |
Average jitter in microseconds. Type: double Default: 0 |
AvgLatency |
Average latency in microseconds. Type: double Default: 0 |
BestLoadIterationNum |
Best load iteration number. Type: u32 Default: 0 |
BurstSize |
Number test frames sent in one burst in one iteration of the test. Type: u64 Default: 0 |
ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
ConfiguredFrameSize |
User configured frame size. Type: double Default: 0 |
DuplicateFrameCount |
Number of duplicate frames received. Type: u64 Default: 0 |
ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
FcsErrorFrameCount |
Number of frames received with FCS errors. Type: u64 Default: 0 |
FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
ForwardingRate |
Rate at which frames are received in fps. Type: double Default: 0 |
FrameLengthDistribution |
Name of the iMIX distribution when frame size type is iMIX. Type: string Default: N/A |
FrameLoss |
Total number of test frames expected, but not received during the test. Type: u64 Default: 0 |
FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
FrameSize |
Frame size. Type: double Default: 0 |
FrameSizeType |
Frame size type. Type: string Default: 0 |
HistBin10Count |
Histogram bucket 10. Type: u64 Default: 0 |
HistBin11Count |
Histogram bucket 11. Type: u64 Default: 0 |
HistBin12Count |
Histogram bucket 12. Type: u64 Default: 0 |
HistBin13Count |
Histogram bucket 13. Type: u64 Default: 0 |
HistBin14Count |
Histogram bucket 14. Type: u64 Default: 0 |
HistBin15Count |
Histogram bucket 15. Type: u64 Default: 0 |
HistBin16Count |
Histogram bucket 16. Type: u64 Default: 0 |
HistBin1Count |
Histogram bucket 1. Type: u64 Default: 0 |
HistBin2Count |
Histogram bucket 2. Type: u64 Default: 0 |
HistBin3Count |
Histogram bucket 3. Type: u64 Default: 0 |
HistBin4Count |
Histogram bucket 4. Type: u64 Default: 0 |
HistBin5Count |
Histogram bucket 5. Type: u64 Default: 0 |
HistBin6Count |
Histogram bucket 6. Type: u64 Default: 0 |
HistBin7Count |
Histogram bucket 7. Type: u64 Default: 0 |
HistBin8Count |
Histogram bucket 8. Type: u64 Default: 0 |
HistBin9Count |
Histogram bucket 9. Type: u64 Default: 0 |
IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
IntendedLoad |
Intended load in percentage. Type: double Default: 0 |
IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
IntendedPCTLoad |
Intended load in frames per second. Type: double Default: 0 |
Ipv4AvgJitter |
Average jitter in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4AvgLatency |
Average latency in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4FrameLoss |
Number of IPv4 frames lost. Type: u64 Default: 0 |
Ipv4IntendedBpsLoad |
IPv4 Intended Load rate in bits per second. Type: double Default: 0 |
Ipv4IntendedFPSLoad |
IPv4 Intended Load rate in frames per second. Type: double Default: 0 |
Ipv4IntendedIBGLoad |
IPv4 Intended Load rate in inter burst gaps. Type: double Default: 0 |
Ipv4IntendedKbpsLoad |
IPv4 Intended Load rate in kilobits per second. Type: double Default: 0 |
Ipv4IntendedLoad |
Intended load for IPv4 traffic. Type: double Default: 0 |
Ipv4IntendedMbpsLoad |
IPv4 Intended Load rate in megabits per second. Type: double Default: 0 |
Ipv4IntendedPCTLoad |
IPv4 Intended Load rate in percentage. Type: double Default: 0 |
Ipv4MaxJitter |
Maximum jitter in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4MaxLatency |
Maximum latency in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4MinJitter |
Minimum jitter in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4MinLatency |
Minimum latency in microseconds of IPv4 traffic. Type: double Default: 0 |
Ipv4OfferedBpsLoad |
IPv4 offered load rate in bits per second. Type: double Default: 0 |
Ipv4OfferedFPSLoad |
IPv4 offered load rate in frames per second. Type: double Default: 0 |
Ipv4OfferedIBGLoad |
IPv4 offered load rate in inter burst gaps. Type: double Default: 0 |
Ipv4OfferedKbpsLoad |
IPv4 offered load rate in kilobits per second. Type: double Default: 0 |
Ipv4OfferedLoad |
Offered load for IPv4 traffic. Type: double Default: 0 |
Ipv4OfferedMbpsLoad |
IPv4 offered load rate in megabits per second. Type: double Default: 0 |
Ipv4OfferedPCTLoad |
IPv4 offered load rate in percentage. Type: double Default: 0 |
Ipv4RxFrameCount |
Number of IPv4 frames received. Type: u64 Default: 0 |
Ipv4TxFrameCount |
Number of IPv4 frames transmitted. Type: u64 Default: 0 |
Ipv4TxFrameRate |
Number of IPv4 frames transmitted per second. Type: double Default: 0 |
Ipv6AvgJitter |
Average jitter in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6AvgLatency |
Average latency in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6ExtensionHeader |
IPv6 extension header. Type: string Default: N/A |
Ipv6FrameLoss |
Number of IPv6 frames lost. Type: u64 Default: 0 |
Ipv6IntendedBpsLoad |
IPv6 Intended Load rate in bits per second. Type: double Default: 0 |
Ipv6IntendedFPSLoad |
IPv6 Intended Load in Frames Per Second Type: double Default: 0 |
Ipv6IntendedIBGLoad |
IPv6 Intended Load in Inter Burst gap. Type: double Default: 0 |
Ipv6IntendedKbpsLoad |
IPv6 Intended Load rate in kilobits per second. Type: double Default: 0 |
Ipv6IntendedLoad |
Intended load for IPv6 traffic. Type: double Default: 0 |
Ipv6IntendedMbpsLoad |
IPv6 Intended Load rate in megabits per second. Type: double Default: 0 |
Ipv6IntendedPCTLoad |
IPv6 Intended Load rate in percentage. Type: double Default: 0 |
Ipv6Ipv4CoexistenceRatio |
IPv6 to IPv4 Coexistence Ratio in terms of weights. Type: string Default: N/A |
Ipv6MaxJitter |
Maximum jitter in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6MaxLatency |
Maximum latency in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6MinJitter |
Minimum jitter in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6MinLatency |
Minimum latency in microseconds of IPv6 traffic. Type: double Default: 0 |
Ipv6OfferedBpsLoad |
IPv6 offered load rate in bits per second. Type: double Default: 0 |
Ipv6OfferedFPSLoad |
IPv6 offered load rate in frames per second. Type: double Default: 0 |
Ipv6OfferedIBGLoad |
IPv6 offered load rate in inter burst gaps. Type: double Default: 0 |
Ipv6OfferedKbpsLoad |
IPv6 offered load rate in kilobits per second. Type: double Default: 0 |
Ipv6OfferedLoad |
Offered load for IPv6 traffic. Type: double Default: 0 |
Ipv6OfferedMbpsLoad |
IPv6 offered load rate in megabits per second. Type: double Default: 0 |
Ipv6OfferedPCTLoad |
IPv6 offered load rate in percentage. Type: double Default: 0 |
Ipv6RxFrameCount |
Number of IPv6 frames received. Type: u64 Default: 0 |
Ipv6TxFrameCount |
Number of IPv6 frames transmitted. Type: u64 Default: 0 |
Ipv6TxFrameRate |
Number of IPv6 frames transmitted per second. Type: double Default: 0 |
IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Iteration number. Type: u8 Default: 0 |
LoadResult |
Load result. Type: string Default: "" (empty string) |
LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load value. Type: double Default: 0 |
LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
MaxJitter |
Maximum jitter in microseconds. Type: double Default: 0 |
MaxLatency |
Maximum latency in microseconds. Type: double Default: 0 |
MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Offered load (OLoad) in megabits per second. Type: double Default: 0 |
MinJitter |
Minimum jitter in microseconds. Type: double Default: 0 |
MinLatency |
Minimum latency in microseconds. Type: double Default: 0 |
OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
OfferedLoad |
Offered load. Type: double Default: 0 |
OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
OutOfSeqCount |
Total number of test frames received in an order different from the order in which they were transmitted. Type: u64 Default: 0 |
PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
PercentLoss |
Frame loss percentage. Type: double Default: 0 |
PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
PortHandle |
Port handle. Type: handle Default: 0 |
Profile |
Profile name. Type: string Default: "" (empty string) |
ProfileHnd |
Profile handle. Type: handle Default: 0 |
QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
Result |
A value of Passed/Failed is return from the iteration test. Type: string Default: Failed |
RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
RxFrameCount |
Number of frames received. Type: u64 Default: 0 |
RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
SearchKey |
Unique search configuration identifier for traffic loop. Type: string Default: N/A |
StreamBlock |
Stream block. Type: string Default: "" (empty string) |
StreamBlockHandle |
Stream block handle. Type: handle Default: 0 |
TrafficGroupWeightRatio |
Traffic group weight ratio. Type: string Default: N/A |
TrialNum |
Trial number. Type: u8 Default: 0 |
TxBitRate |
Rate at which bits are transmitted. Type: double Default: 0 |
TxFrameCount |
Total number of frames transmitted. Type: u64 Default: 0 |
TxFrameRate |
Rate at which frames are transmitted in fps. Type: double Default: 0 |
TxMbpsLoad |
Intended load (ILoad) in megabits per second. Type: double Default: 0 |
TxOctetCount |
Total number of octets transmitted. Type: u64 Default: 0 |
TxPort |
Transmitting port. Type: string Default: "" (empty string) |
TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |