Description:
Used in the end of test result database. You cannot subscribe to this object to get results.
Parents: Project
Relations:
| Side name (Type) |
Relative | Description |
|---|---|---|
| ResultParent (ResultChild) |
Use this to connect a results object to an object. |
| Attribute | Description | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
| Read-Only Attribute | Description |
|---|---|
| AvgJitter |
Average jitter value calculated from all measured jitter values in microseconds. Type: double Default: 0 |
| AvgLatency |
Average latency value calculated from all measured latency values in microseconds. Type: double Default: 0 |
| BurstSize |
Number test frames sent in one burst in one iteration of the test. Type: u64 Default: 0 |
| ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
| ConfiguredFrameSize |
User configured frame size. Type: double Default: 0 |
| DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
| DurationInSec |
Duration test traffic was transmitted in seconds. Type: double Default: 0 |
| ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
| FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
| FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
| FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
| ForwardingRate |
Measured, average forwarding rate of the Device Under Test (DUT) in frames per second (fps) during the test. Type: double Default: 0 |
| FrameLengthDistribution |
iMIX distribution. Type: string Default: N/A |
| FrameLoss |
Frame loss. Type: u64 Default: 0 |
| FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
| FrameSize |
Frame size. Type: double Default: 0 |
| FrameSizeType |
Frame size iteration mode. Type: string Default: 0 |
| IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
| IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
| IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
| IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
| IntendedLoad |
Number of frames per second that the application attempts to transmit to a DUT/SUT for forwarding to a specified output interface or interfaces. Type: double Default: 0 |
| IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
| IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
| IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Iteration number. Type: u8 Default: 0 |
| LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load. Type: double Default: 0 |
| LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
| MaxJitter |
Largest measured jitter value in the set of all measured jitter values in microseconds. Type: double Default: 0 |
| MaxLatency |
Largest measured latency value in the set of all measured latency values in microseconds. Type: double Default: 0 |
| MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Offered load (OLoad) in megabits per second. Type: double Default: 0 |
| MinJitter |
Smallest measured jitter value in the set of all measured jitter values in microseconds. Type: double Default: 0 |
| MinLatency |
Smallest measured latency value in the set of all measured latency values in microseconds. Type: double Default: 0 |
| OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
| OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
| OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
| OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
| OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
| OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
| OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
| OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
| OutOfSeqCount |
Total number of test frames received in an order different from the order in which they were transmitted. Type: u64 Default: 0 |
| PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
| PercentLoss |
Percentage of test frames that were expected, but not received. Type: double Default: 0 |
| PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
| QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
| RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
| RxFrameCount |
Received frame count. Type: u64 Default: 0 |
| RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
| RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
| SearchKey |
Unique search configuration identifier for traffic loop. Type: string Default: N/A |
| TrafficGroupWeightRatio |
Traffic group weight ratio. Type: string Default: N/A |
| TrialNum |
Number of the current trial. Type: u8 Default: 0 |
| TxFrameCount |
Transmitted frame count. Type: u64 Default: 0 |
| TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
| TxMbpsLoad |
Intended load (ILoad) in megabits per second. Type: double Default: 0 |
| TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |