Description:
Used in the end of test result database. You cannot subscribe to this object to get results.
Parents: Project
Relations:
| Side name (Type) |
Relative | Description |
|---|---|---|
| ResultParent (ResultChild) |
Rfc2544BackToBackFramesConfig, Rfc2544FrameLossConfig, Rfc2544LatencyConfig, Rfc2544ThroughputConfig |
Use this to connect a results object to an object. |
| Attribute | Description | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
| Read-Only Attribute | Description | ||||||
|---|---|---|---|---|---|---|---|
| BurstSize |
Configured burst size use for the test. Type: u64 Default: 0 |
||||||
| ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
||||||
| ConfiguredFrameSize |
User configured frame size. Type: double Default: 0 |
||||||
| DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
||||||
| ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
||||||
| FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
||||||
| FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
||||||
| FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
||||||
| ForwardingRate |
Number of frames per second that a device can be observed to successfully transmit to the correct destination interface in response to a specified offered load. Type: double Default: 0 |
||||||
| FrameLengthDistribution |
Name of the iMIX distribution when frame size type is iMIX. Type: string Default: N/A |
||||||
| FrameLoss |
Total number of test frames expected, but not received during the test. Type: u64 Default: 0 |
||||||
| FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
||||||
| FrameSize |
Frame size. Type: double Default: 0 |
||||||
| FrameSizeType |
Frame size type. Can be Fixed, Random, or iMIX. Type: string Default: 0 |
||||||
| IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
||||||
| IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
||||||
| IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
||||||
| IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
||||||
| IntendedLoad |
Intended load rate. Type: double Default: 0 |
||||||
| IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
||||||
| IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
||||||
| IterationTotal |
Total number of iterations. Type: u8 Default: 0 |
||||||
| LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load value. Type: double Default: 0 |
||||||
| LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
||||||
| MaxLatencyThresholdExceeded |
Whether the maximum latency threshold has been exceeded. Type: bool Default: FALSE Possible Values:
|
||||||
| OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
||||||
| OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
||||||
| OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
||||||
| OfferedKbpsLoad |
Offered load rate in kilobits per second. Type: double Default: 0 |
||||||
| OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
||||||
| OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
||||||
| OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
||||||
| OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
||||||
| OutOfSeqThresholdExceeded |
Whether the out of sequence frames threshold has been exceeded. Type: bool Default: FALSE Possible Values:
|
||||||
| PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
||||||
| PercentLoss |
Frame loss percentage. Type: double Default: 0 |
||||||
| PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
||||||
| QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
||||||
| RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
||||||
| RxFrameCount |
Received frame count. Type: u64 Default: 0 |
||||||
| RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
||||||
| RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
||||||
| ThroughputRate |
Throughput rate. Type: double Default: 0 |
||||||
| TotalFrameLoss |
Total frame loss. Type: u64 Default: 0 |
||||||
| TxFrameCount |
Transmitted frame count. Type: u64 Default: 0 |
||||||
| TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
||||||
| TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |