Description:
Configuration object for RFC 2889 broadcast frame forwarding test.
Parents: Project
Children: BenchmarkEthernet10GigPortConfig
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
TrafficDescriptorGroup (TrafficDescriptorGroupBinding) |
Relation describing the binding to the Traffic Descriptor Group. |
Attribute | Description | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Common Writable Attributes | Active, Name | ||||||||||||||
AcceptableFrameLoss |
Maximum frame loss you want Spirent TestCenter to allow before stopping the test. This value represents the aggregate loss from all flows averaged across each all ports in the test. Type: double Default: 0 Range: 0.0 - 100.0 |
||||||||||||||
Backoff |
Percentage by which the transmission rate will be lowered if the test fails at the current rate. Type: double Default: 50 Range: 0.001 - 99.999 |
||||||||||||||
BurstSizeEnd |
Final burst size when the burst size mode is set to STEP. Type: u32 Default: 1 Range: 1 - 4294967295 |
||||||||||||||
BurstSizeIterationMode |
Mode for adjusting the burst size over all iterations. Type: enum Default: STEP Possible Values:
|
||||||||||||||
BurstSizeStart |
Initial burst size when burst size mode is set to STEP. Type: u32 Default: 1 Range: 1 - 4294967295 |
||||||||||||||
BurstSizeStep |
Step value for the burst size when going from the initial burst size to final burst size over different iterations. Type: u32 Default: 1 Range: 1 - 4294967295 |
||||||||||||||
CustomBurstSizeList |
User defined list of burst sizes used when Burst size mode is set to CUSTOM. Type: u32 Default: 0 Range: 1 - 4294967295 |
||||||||||||||
CustomFrameSizeList |
User defined list of frame sizes. Type: u16 Default: 0 |
||||||||||||||
DelayAfterTransmission |
Delay after transmission in seconds. Type: u16 Default: 15 Range: 1 - 3600 |
||||||||||||||
DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
||||||||||||||
DisplayTrafficGroupLoadUnit |
Display units for traffic group load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
||||||||||||||
DurationBursts |
Transmission length in number of frames. Type: u32 Default: 1000 Range: 1 - 16777215 |
||||||||||||||
DurationMode |
Duration mode for each transmitted stream. Whether to measure test duration in seconds or number of frames. Type: enum Default: SECONDS Possible Values:
|
||||||||||||||
DurationSeconds |
Transmission time in seconds. Type: u32 Default: 30 Range: 1 - 5184000 |
||||||||||||||
EnableDetailedResultsCollection |
Enable collection of detailed results. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
EnableExposedInternalCommands |
Whether to display the expanded sequence of component commands of the benchmarking test being configured. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
EnableFrameSizeOnTest |
Whether to use the frame size specified in the test-level attributes. Type: bool Default: TRUE Possible Values:
|
||||||||||||||
EnableJitterMeasurement |
Allow measuring min, maximum and average jitter values. This is done by running the test in 'Jitter' analyzer result view mode. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
EnableLearning |
Whether to enable learning mode. Type: bool Default: TRUE Possible Values:
|
||||||||||||||
EnablePauseBeforeTraffic |
Whether to pause before starting. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
EnableTrafficVerification |
Boolean to control whether to add verification commands to the test sequence. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
ExternalProcessCommand |
Command to run an user specified external process. Type: string Default: "" (empty string) |
||||||||||||||
FrameSizeEnd |
Maximum frame size when using Step mode for incrementing the frame size. This attribute is ignored if FrameSizeIterationMode is set to RANDOM or CUSTOM. Type: u16 Default: 256 Range: 64 - 16383 |
||||||||||||||
FrameSizeIterationMode |
Mode for adjusting the frame size from iteration to iteration. Type: enum Default: CUSTOM Possible Values:
|
||||||||||||||
FrameSizeStart |
Starting frame size when using Step mode for incrementing the frame size. This attribute is ignored if FrameSizeIterationMode is set to RANDOM or CUSTOM or IMIX. Type: u16 Default: 128 Range: 64 - 16383 |
||||||||||||||
FrameSizeStep |
Step value for incrementing the frame size for Step mode from FrameSizeStart to FrameSizeEnd. This attribute is ignored if FrameSizeIterationMode is set to RANDOM or CUSTOM. Type: u16 Default: 128 Range: 1 - 16383 |
||||||||||||||
IgnoreMinMaxLimits |
Enable the application to automatically define a Min Rate /Max Rate range that successfully yields throughput. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
L2DelayBeforeLearning |
Time in seconds prior to the commencement of training. Type: u16 Default: 2 Range: 0 - 3600 |
||||||||||||||
L2LearningFrameRate |
Layer 2 learning rate in frames per second for the test. Type: u32 Default: 1000 Range: 1 - 4294967295 |
||||||||||||||
L2LearningRepeatCount |
Number of learning retries if transmission errors, learning verification errors, or link errors occur. Type: u16 Default: 5 Range: 1 - 100 |
||||||||||||||
L3DelayBeforeLearning |
Delay in seconds before performing L3 Learning. Type: u16 Default: 2 Range: 0 - 3600 |
||||||||||||||
L3EnableCyclicAddrResolution |
Whether to enable Layer 3 cyclic address resolution. Type: bool Default: TRUE Possible Values:
|
||||||||||||||
L3LearningRate |
Rate to send ARP requests. Type: u32 Default: 1000 |
||||||||||||||
L3RetryCount |
Number of Layer 3 retry attempts allowed. Type: u16 Default: 5 Range: 1 - 100 |
||||||||||||||
LatencyType |
Latency type for different devices. Type: enum Default: LILO Possible Values:
|
||||||||||||||
LearningFreqMode |
Learning frequency. Type: enum Default: LEARN_ONCE Possible Values:
|
||||||||||||||
LearningMode |
Learning mode. Type: enum Default: L2_LEARNING Possible Values:
|
||||||||||||||
NumOfTrials |
Number of times the test repeats with its initial configuration. Each trial is based on the same parameter values. Within a trial, certain parameter values vary with each iteration, according to the test methodology and setup. At the start of the next trial, these parameters revert to their initial values. Type: u16 Default: 1 Range: 1 - 60 |
||||||||||||||
RandomMaxFrameSize |
When using random mode for FrameSizeIterationMode, the maximum frame size. This attribute is ignored if FrameSizeIterationMode is set to STEP or CUSTOM. Type: u16 Default: 256 Range: 64 - 16383 |
||||||||||||||
RandomMinFrameSize |
When using random mode for FrameSizeIterationMode, the minimum frame size. This attribute is ignored if FrameSizeIterationMode is set to STEP or CUSTOM. Type: u16 Default: 128 Range: 64 - 16383 |
||||||||||||||
RateInitial |
Transmission rate for the first iteration of the test. This is a percentage of the full wire rate. Type: double Default: 10 Range: 0.001 - 100.0 |
||||||||||||||
RateLowerLimit |
Lowest transmission rate at which the application will send traffic during any test iteration, as a percentage of the total wire rate. Type: double Default: 1 Range: 0.001 - 100.0 |
||||||||||||||
RateStep |
Percent by which Spirent TestCenter will increase the current transmission rate, as a percentage of the total wire rate. The transmission rate increases until the maximum rate is reached, even if there is frame loss. Type: double Default: 10 Range: 0.001 - 100.0 |
||||||||||||||
RateUpperLimit |
Maximum rate at which Spirent TestCenter will send traffic during the test,as a percentage of the total wire rate. Type: double Default: 100 Range: 0.001 - 100.0 |
||||||||||||||
Resolution |
Finest adjustment possible, in number of frames, for the duration of transmitted frames from iteration to iteration. Type: double Default: 1 Range: 0.001 - 100.0 |
||||||||||||||
ResultsOption |
Results Option for the test Type: enum Default: CLASSIC Possible Values:
|
||||||||||||||
RunExternalProcessBeforeTraffic |
Allows user to run an external process before generating and transmitting traffic. Type: bool Default: FALSE Possible Values:
|
||||||||||||||
SearchMode |
Mode used to find the throughput rate. Type: enum Default: BINARY Possible Values:
|
||||||||||||||
StaggerStartDelay |
Delay between starting successive ports, in milliseconds. Type: u16 Default: 0 Range: 0 - 65535 |
||||||||||||||
TrafficStartDelay |
When to begin the traffic start delay. Type: double Default: 2 Range: 0.005 - 3600 |
||||||||||||||
TrafficStartDelayMode |
When to begin the traffic start delay. Type: enum Default: AFTER_TEST Possible Values:
|
||||||||||||||
TrafficVerificationAbortOnFail |
Test behavior when traffic verification fails. Type: bool Default: TRUE Possible Values:
|
||||||||||||||
TrafficVerificationFreqMode |
Specifies when to perform traffic verification during the test. Type: enum Default: VERIFY_EVERY_ITERATION Possible Values:
|
||||||||||||||
TrafficVerificationTxFrameCount |
Number of frames to use for traffic verification. Type: u16 Default: 100 Range: 1 - 32767 |
||||||||||||||
TrafficVerificationTxFrameRate |
Traffic rate in frames per second to use for traffic verification. Type: u32 Default: 1000 Range: 1 - 14880952 |
There are no read-only attributes.