Description:
Used in the end of test result database. You cannot subscribe to this object to get results.
Parents: Project
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
ResultParent (ResultChild) |
Use this to connect a results object to an object. |
Attribute | Description | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
Read-Only Attribute | Description |
---|---|
AvgJitter |
Average jitter value calculated from all measured jitter values in microseconds. Type: double Default: 0 |
AvgLatency |
Average latency value calculated from all measured latency values in microseconds. Type: double Default: 0 |
BurstSize |
Configured burst size use for the test. Type: u64 Default: 0 |
ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
ConfiguredFrameSize |
User configured frame size. Type: double Default: 0 |
DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
ExpectedFrameCount |
Number of frames expected to be transmitted. Type: u64 Default: 0 |
FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames flooded. Type: u64 Default: 0 |
FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
ForwardingRate |
Number of frames per second that a device can be observed to successfully transmit to the correct destination interface in response to a specified offered load. Type: double Default: 0 |
FrameLengthDistribution |
Name of the iMIX distribution when frame size type is iMIX. Type: string Default: N/A |
FrameLoss |
Number of frames lost. Type: u64 Default: 0 |
FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames transmitted during the last one-second interval. Type: double Default: 0 |
FrameSize |
Frame size. Type: double Default: 0 |
FrameSizeType |
Frame size type. Type: string Default: 0 |
IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
IntendedLoad |
Number of frames per second that the application attempts to transmit to a DUT/SUT for forwarding to a specified output interface or interfaces. Type: double Default: 0 |
IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Iteration number. Type: u8 Default: 0 |
LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load. Type: double Default: 0 |
LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
MaxJitter |
Largest measured jitter value in the set of all measured jitter values in microseconds. Type: double Default: 0 |
MaxLatency |
Largest measured latency value in the set of all measured latency values in microseconds. Type: double Default: 0 |
MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Offered load (OLoad) in megabits per second. Type: double Default: 0 |
MinJitter |
Smallest measured jitter value in the set of all measured jitter values in microseconds. Type: double Default: 0 |
MinLatency |
Smallest measured latency value in the set of all measured latency values in microseconds. Type: double Default: 0 |
OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
OutOfSeqCount |
Total number of test frames received in an order different from the order in which they were transmitted. Type: u64 Default: 0 |
PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
PercentLoss |
Frame loss percentage. Type: double Default: 0 |
PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
Result |
Iteration result indicating if the traffic at the given rate satisfied the pass condition for throughput. Type: string Default: Failed |
RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames expected to be received. Type: u64 Default: 0 |
RxFrameCount |
Number of frames received. Type: u64 Default: 0 |
RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of non-signature frames received. Type: u64 Default: 0 |
RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of Spirent signature frames received. Type: u64 Default: 0 |
Throughput |
Throughput measured in frames per second. Type: double Default: 0 |
TrialNum |
Number of the current trial. Type: u8 Default: 0 |
TxFrameCount |
Total number of frames transmitted. Type: u64 Default: 0 |
TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
TxMbpsLoad |
Intended load (ILoad) in megabits per second. Type: double Default: 0 |
TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of Spirent signature frames transmitted. Type: u64 Default: 0 |