Description:
Used in the end of test result database. You cannot subscribe to this object to get results.
Parents: Project
Relations:
| Side name (Type) |
Relative | Description |
|---|---|---|
| ResultParent (ResultChild) |
Use this to connect a results object to an object. |
| Attribute | Description | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
| Read-Only Attribute | Description |
|---|---|
| BurstSize |
Configured burst size use for the test. Type: u64 Default: 0 |
| ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
| ConfiguredFrameSize |
User configured frame size. Type: double Default: 0 |
| DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
| ExpectedFrameCount |
Number of frames expected to be transmitted. Type: u64 Default: 0 |
| FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
| FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames flooded. Type: u64 Default: 0 |
| FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
| ForwardingRate |
Number of frames per second that a device can be observed to successfully transmit to the correct destination interface in response to a specified offered load. Type: double Default: 0 |
| FrameLengthDistribution |
Name of the iMIX distribution when frame size type is iMIX. Type: string Default: N/A |
| FrameLoss |
Number of frames lost. Type: u64 Default: 0 |
| FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames transmitted during the last one-second interval. Type: double Default: 0 |
| FrameSize |
Frame size. Type: double Default: 0 |
| FrameSizeType |
Frame size type. Can be Fixed, Random, or iMIX. Type: string Default: 0 |
| IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
| IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
| IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
| IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
| IntendedLoad |
Number of frames per second that the application attempts to transmit to a DUT/SUT for forwarding to a specified output interface or interfaces. Type: double Default: 0 |
| IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
| IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
| IterationTotal |
Total number of iterations. Type: u8 Default: 0 |
| LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load. Type: double Default: 0 |
| LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
| OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
| OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
| OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
| OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
| OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
| OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
| OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
| OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
| PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
| PercentLoss |
Frame loss percentage. Type: double Default: 0 |
| PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
| QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
| RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of frames expected to be received. Type: u64 Default: 0 |
| RxFrameCount |
Number of frames received. Type: u64 Default: 0 |
| RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of non-signature frames received. Type: u64 Default: 0 |
| RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of Spirent signature frames received. Type: u64 Default: 0 |
| Throughput |
Throughput measured in frames per second. Type: double Default: 0 |
| TxFrameCount |
Total number of frames transmitted. Type: u64 Default: 0 |
| TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
| TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Number of Spirent signature frames transmitted. Type: u64 Default: 0 |