Description:
Rfc8239 Incast Per Max Burst Size Summary Result.
Parents: Project
Relations:
| Side name (Type) |
Relative | Description |
|---|---|---|
| ResultParent (ResultChild) |
Use this to connect a results object to an object. |
| Attribute | Description | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
| Read-Only Attribute | Description |
|---|---|
| AvgJitter |
Average Jitter (us). Type: double Default: 0 |
| AvgLatency |
Average Latency (us). Type: double Default: 0 |
| AvgReceiveRate |
Average Receive Rate in bps. Type: double Default: 0 |
| AvgSendRate |
Average Send Rate in bps. Type: double Default: 0 |
| Bandwidth |
Network Bandwidth. Type: u64 Default: 0 |
| BurstSize |
Burst Size. Type: u64 Default: 0 |
| ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
| ConfiguredFrameSize |
Configured Tx Frame Size. Type: double Default: 0 |
| CumulativeReceiveRate |
Cumulative Receive Rate in bps. Type: double Default: 0 |
| CumulativeSendRate |
Cumulative Send Rate in bps. Type: double Default: 0 |
| DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
| EgressPortName |
Name of Egress Ports. Type: string Default: 0 |
| ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
| FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
| FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
| FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
| ForwardingRate |
Forwarding Rate (fps). Type: double Default: 0 |
| FrameLengthDistribution |
iMIX Distribution. Type: string Default: N/A |
| FrameLoss |
Total number of test frames expected, but not received during the test. Type: u64 Default: 0 |
| FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
| FrameSize |
Average Tx Frame Size. Type: double Default: 0 |
| FrameSizeType |
Frame Size Type. Type: string Default: 0 |
| HistBin10Count |
Histogram Bucket 10. Type: u64 Default: 0 |
| HistBin11Count |
Histogram Bucket 11. Type: u64 Default: 0 |
| HistBin12Count |
Histogram Bucket 12. Type: u64 Default: 0 |
| HistBin13Count |
Histogram Bucket 13. Type: u64 Default: 0 |
| HistBin14Count |
Histogram Bucket 14. Type: u64 Default: 0 |
| HistBin15Count |
Histogram Bucket 15. Type: u64 Default: 0 |
| HistBin16Count |
Histogram Bucket 16. Type: u64 Default: 0 |
| HistBin1Count |
Histogram Bucket 1. Type: u64 Default: 0 |
| HistBin2Count |
Histogram Bucket 2. Type: u64 Default: 0 |
| HistBin3Count |
Histogram Bucket 3. Type: u64 Default: 0 |
| HistBin4Count |
Histogram Bucket 4. Type: u64 Default: 0 |
| HistBin5Count |
Histogram Bucket 5. Type: u64 Default: 0 |
| HistBin6Count |
Histogram Bucket 6. Type: u64 Default: 0 |
| HistBin7Count |
Histogram Bucket 7. Type: u64 Default: 0 |
| HistBin8Count |
Histogram Bucket 8. Type: u64 Default: 0 |
| HistBin9Count |
Histogram Bucket 9. Type: u64 Default: 0 |
| IngressPortName |
Name of Ingress Ports. Type: string Default: 0 |
| IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
| IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
| IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
| IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
| IntendedLoad |
Intended Load. Type: double Default: 0 |
| IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
| IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
| Ipv4AvgJitter |
IPv4 Average Jitter (us). Type: double Default: 0 |
| Ipv4AvgLatency |
IPv4 Average Latency (us). Type: double Default: 0 |
| Ipv4FrameLoss |
IPv4 Dropped Frame Count. Type: u64 Default: 0 |
| Ipv4IntendedBpsLoad |
IPv4 Intended Load in bps. Type: double Default: 0 |
| Ipv4IntendedFPSLoad |
IPv4 Intended Load in Frames Per Second. Type: double Default: 0 |
| Ipv4IntendedIBGLoad |
IPv4 Intended Load in Inter Burst gap. Type: double Default: 0 |
| Ipv4IntendedKbpsLoad |
IPv4 Intended Load in Kbps. Type: double Default: 0 |
| Ipv4IntendedLoad |
IPv4 Intended Load. Type: double Default: 0 |
| Ipv4IntendedMbpsLoad |
IPv4 Intended Load in Mbps. Type: double Default: 0 |
| Ipv4IntendedPCTLoad |
IPv4 Intended Load in percent. Type: double Default: 0 |
| Ipv4MaxJitter |
IPv4 Maximum Jitter (us). Type: double Default: 0 |
| Ipv4MaxLatency |
IPv4 Maximum Latency (us). Type: double Default: 0 |
| Ipv4MinJitter |
IPv4 Minimum Jitter (us). Type: double Default: 0 |
| Ipv4MinLatency |
IPv4 Minimum Latency (us). Type: double Default: 0 |
| Ipv4OfferedBpsLoad |
IPv4 Offered Load in bps. Type: double Default: 0 |
| Ipv4OfferedFPSLoad |
IPv4 Offered Load in Frames Per Second. Type: double Default: 0 |
| Ipv4OfferedIBGLoad |
IPv4 Offered Load in Inter Burst gap. Type: double Default: 0 |
| Ipv4OfferedKbpsLoad |
IPv4 Offered Load in Kbps. Type: double Default: 0 |
| Ipv4OfferedLoad |
IPv4 Offered Load. Type: double Default: 0 |
| Ipv4OfferedMbpsLoad |
IPv4 Offered Load in Mbps. Type: double Default: 0 |
| Ipv4OfferedPCTLoad |
IPv4 Offered Load in percent. Type: double Default: 0 |
| Ipv4RxFrameCount |
IPv4 Rx Frame Count. Type: u64 Default: 0 |
| Ipv4TxFrameCount |
IPv4 Tx Frame Count. Type: u64 Default: 0 |
| Ipv4TxFrameRate |
IPv4 Tx Frame Rate. Type: double Default: 0 |
| Ipv6AvgJitter |
IPv6 Average Jitter (us). Type: double Default: 0 |
| Ipv6AvgLatency |
IPv6 Average Latency (us). Type: double Default: 0 |
| Ipv6ExtensionHeader |
IPv6 Extension Header. Type: string Default: N/A |
| Ipv6FrameLoss |
IPv6 Dropped Frame Count. Type: u64 Default: 0 |
| Ipv6IntendedBpsLoad |
IPv6 Intended Load in bps. Type: double Default: 0 |
| Ipv6IntendedFPSLoad |
IPv6 Intended Load in Frames Per Second. Type: double Default: 0 |
| Ipv6IntendedIBGLoad |
IPv6 Intended Load in Inter Burst gap. Type: double Default: 0 |
| Ipv6IntendedKbpsLoad |
IPv6 Intended Load in Kbps. Type: double Default: 0 |
| Ipv6IntendedLoad |
IPv6 Intended Load. Type: double Default: 0 |
| Ipv6IntendedMbpsLoad |
IPv6 Intended Load in Mbps. Type: double Default: 0 |
| Ipv6IntendedPCTLoad |
IPv6 Intended Load in percent. Type: double Default: 0 |
| Ipv6Ipv4CoexistenceRatio |
IPv6-IPv4 Coexistence Ratio. Type: string Default: N/A |
| Ipv6MaxJitter |
IPv6 Maximum Jitter (us). Type: double Default: 0 |
| Ipv6MaxLatency |
IPv6 Maximum Latency (us). Type: double Default: 0 |
| Ipv6MinJitter |
IPv6 Minimum Jitter (us). Type: double Default: 0 |
| Ipv6MinLatency |
IPv6 Minimum Latency (us). Type: double Default: 0 |
| Ipv6OfferedBpsLoad |
IPv6 Offered Load in bps. Type: double Default: 0 |
| Ipv6OfferedFPSLoad |
IPv6 Offered Load in Frames Per Second. Type: double Default: 0 |
| Ipv6OfferedIBGLoad |
IPv6 Offered Load in Inter Burst gap. Type: double Default: 0 |
| Ipv6OfferedKbpsLoad |
IPv6 Offered Load in Kbps. Type: double Default: 0 |
| Ipv6OfferedLoad |
IPv6 Offered Load. Type: double Default: 0 |
| Ipv6OfferedMbpsLoad |
IPv6 Offered Load in Mbps. Type: double Default: 0 |
| Ipv6OfferedPCTLoad |
IPv6 Offered Load in percent. Type: double Default: 0 |
| Ipv6RxFrameCount |
IPv6 Rx Frame Count. Type: u64 Default: 0 |
| Ipv6TxFrameCount |
IPv6 Tx Frame Count. Type: u64 Default: 0 |
| Ipv6TxFrameRate |
IPv6 Tx Frame Rate. Type: double Default: 0 |
| IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Trial Number. Type: u8 Default: 0 |
| LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load value. Type: double Default: 0 |
| LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
| MaxJitter |
Maximum Jitter (us). Type: double Default: 0 |
| MaxLatency |
Maximum Latency (us). Type: double Default: 0 |
| MaxReceiveRate |
Maximum Receive Rate in bps. Type: double Default: 0 |
| MaxSendRate |
Maximum Send Rate in bps. Type: double Default: 0 |
| MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Tx Rate (Mbps). Type: double Default: 0 |
| MinJitter |
Minimum Jitter (us). Type: double Default: 0 |
| MinLatency |
Minimum Latency (us). Type: double Default: 0 |
| MinReceiveRate |
Minimum Receive Rate in bps. Type: double Default: 0 |
| MinSendRate |
Minimum Send Rate in bps. Type: double Default: 0 |
| NumEgressPorts |
Number of Egress Ports. Type: u32 Default: 0 |
| NumIngressPorts |
Number of Ingress Ports. Type: u32 Default: 0 |
| OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
| OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
| OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
| OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
| OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
| OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
| OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
| OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
| OutOfSeqCount |
Out of Sequence Count. Type: u64 Default: 0 |
| PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
| PayloadSize |
Payload Size. Type: double Default: 0 |
| PercentLoss |
Percentage of test frames that were expected, but not received. Type: double Default: 0 |
| PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
| PortType |
TCP or UDP. Type: string Default: 0 |
| QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
| ReceiveRate |
Receive Rate in bps. Type: double Default: 0 |
| RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
| RxFrameCount |
Received frame count. Type: u64 Default: 0 |
| RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
| RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
| SendRate |
Send Rate in bps. Type: double Default: 0 |
| TrialNum |
Trial Number. Type: u8 Default: 0 |
| TxFrameCount |
Transmitted frame count. Type: u64 Default: 0 |
| TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
| TxMbpsLoad |
Layer 1 Tx Rate (Mbps). Type: double Default: 0 |
| TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |