Description:
Rfc8239 Incast Test Per Iteration Result.
Parents: Project
Relations:
| Side name (Type) |
Relative | Description |
|---|---|---|
| ResultParent (ResultChild) |
Use this to connect a results object to an object. |
| Attribute | Description | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DisplayLoadUnit |
Display Load Unit. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
| Read-Only Attribute | Description |
|---|---|
| AvgJitter |
Average Jitter (us). Type: double Default: 0 |
| AvgLatency |
Average Latency (us). Type: double Default: 0 |
| AvgReceiveRate |
Average Receive Rate in bps. Type: double Default: 0 |
| AvgSendRate |
Average Send Rate in bps. Type: double Default: 0 |
| Bandwidth |
Network Bandwidth. Type: u64 Default: 0 |
| BurstSize |
Burst Size. Type: u64 Default: 0 |
| ChecksumErrorCount |
Rx Checksum Error Count. Type: u64 Default: 0 |
| ConfiguredFrameSize |
Configured Tx Frame Size. Type: double Default: 0 |
| CumulativeReceiveRate |
Cumulative Receive Rate in bps. Type: double Default: 0 |
| CumulativeSendRate |
Cumulative Send Rate in bps. Type: double Default: 0 |
| DuplicateFrameCount |
Rx Duplicate Frame Count. Type: u64 Default: 0 |
| EgressPortName |
Name of Egress Ports. Type: string Default: 0 |
| ExpectedFrameCount |
Expected Frame Count. Type: u64 Default: 0 |
| FcsErrorFrameCount |
Rx FCS Error Frame Count. Type: u64 Default: 0 |
| FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rx Flooded Frame Count. Type: u64 Default: 0 |
| FloodedFrameCount |
Rx Flooded Frame Count. Type: u64 Default: 0 |
| ForwardingRate |
Forwarding Rate (fps). Type: double Default: 0 |
| FrameLengthDistribution |
iMIX Distribution. Type: string Default: N/A |
| FrameLoss |
Dropped Frame Count. Type: u64 Default: 0 |
| FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Tx Frame Rate. Type: double Default: 0 |
| FrameSize |
Average Tx Frame Size. Type: double Default: 0 |
| FrameSizeType |
Frame Size Type. Type: string Default: 0 |
| HistBin10Count |
Histogram Bucket 10. Type: u64 Default: 0 |
| HistBin11Count |
Histogram Bucket 11. Type: u64 Default: 0 |
| HistBin12Count |
Histogram Bucket 12. Type: u64 Default: 0 |
| HistBin13Count |
Histogram Bucket 13. Type: u64 Default: 0 |
| HistBin14Count |
Histogram Bucket 14. Type: u64 Default: 0 |
| HistBin15Count |
Histogram Bucket 15. Type: u64 Default: 0 |
| HistBin16Count |
Histogram Bucket 16. Type: u64 Default: 0 |
| HistBin1Count |
Histogram Bucket 1. Type: u64 Default: 0 |
| HistBin2Count |
Histogram Bucket 2. Type: u64 Default: 0 |
| HistBin3Count |
Histogram Bucket 3. Type: u64 Default: 0 |
| HistBin4Count |
Histogram Bucket 4. Type: u64 Default: 0 |
| HistBin5Count |
Histogram Bucket 5. Type: u64 Default: 0 |
| HistBin6Count |
Histogram Bucket 6. Type: u64 Default: 0 |
| HistBin7Count |
Histogram Bucket 7. Type: u64 Default: 0 |
| HistBin8Count |
Histogram Bucket 8. Type: u64 Default: 0 |
| HistBin9Count |
Histogram Bucket 9. Type: u64 Default: 0 |
| IngressPortName |
Name of Ingress Ports. Type: string Default: 0 |
| IntendedBpsLoad |
Intended Load in bps. Type: double Default: 0 |
| IntendedFPSLoad |
Intended Load in Frames Per Second. Type: double Default: 0 |
| IntendedIBGLoad |
Intended Load in Inter Burst gap. Type: double Default: 0 |
| IntendedKbpsLoad |
Intended Load in Kbps. Type: double Default: 0 |
| IntendedLoad |
Intended Load. Type: double Default: 0 |
| IntendedMbpsLoad |
Intended Load in Mbps. Type: double Default: 0 |
| IntendedPCTLoad |
Intended Load in percent. Type: double Default: 0 |
| Ipv4AvgJitter |
IPv4 Average Jitter (us). Type: double Default: 0 |
| Ipv4AvgLatency |
IPv4 Average Latency (us). Type: double Default: 0 |
| Ipv4FrameLoss |
IPv4 Dropped Frame Count. Type: u64 Default: 0 |
| Ipv4IntendedBpsLoad |
IPv4 Intended Load in bps. Type: double Default: 0 |
| Ipv4IntendedFPSLoad |
IPv4 Intended Load in Frames Per Second. Type: double Default: 0 |
| Ipv4IntendedIBGLoad |
IPv4 Intended Load in Inter Burst gap. Type: double Default: 0 |
| Ipv4IntendedKbpsLoad |
IPv4 Intended Load in Kbps. Type: double Default: 0 |
| Ipv4IntendedLoad |
IPv4 Intended Load. Type: double Default: 0 |
| Ipv4IntendedMbpsLoad |
IPv4 Intended Load in Mbps. Type: double Default: 0 |
| Ipv4IntendedPCTLoad |
IPv4 Intended Load in percent. Type: double Default: 0 |
| Ipv4MaxJitter |
IPv4 Maximum Jitter (us). Type: double Default: 0 |
| Ipv4MaxLatency |
IPv4 Maximum Latency (us). Type: double Default: 0 |
| Ipv4MinJitter |
IPv4 Minimum Jitter (us). Type: double Default: 0 |
| Ipv4MinLatency |
IPv4 Minimum Latency (us). Type: double Default: 0 |
| Ipv4OfferedBpsLoad |
IPv4 Offered Load in bps. Type: double Default: 0 |
| Ipv4OfferedFPSLoad |
IPv4 Offered Load in Frames Per Second. Type: double Default: 0 |
| Ipv4OfferedIBGLoad |
IPv4 Offered Load in Inter Burst gap. Type: double Default: 0 |
| Ipv4OfferedKbpsLoad |
IPv4 Offered Load in Kbps. Type: double Default: 0 |
| Ipv4OfferedLoad |
IPv4 Offered Load. Type: double Default: 0 |
| Ipv4OfferedMbpsLoad |
IPv4 Offered Load in Mbps. Type: double Default: 0 |
| Ipv4OfferedPCTLoad |
IPv4 Offered Load in percent. Type: double Default: 0 |
| Ipv4RxFrameCount |
IPv4 Rx Frame Count. Type: u64 Default: 0 |
| Ipv4TxFrameCount |
IPv4 Tx Frame Count. Type: u64 Default: 0 |
| Ipv4TxFrameRate |
IPv4 Tx Frame Rate. Type: double Default: 0 |
| Ipv6AvgJitter |
IPv6 Average Jitter (us). Type: double Default: 0 |
| Ipv6AvgLatency |
IPv6 Average Latency (us). Type: double Default: 0 |
| Ipv6ExtensionHeader |
IPv6 Extension Header. Type: string Default: N/A |
| Ipv6FrameLoss |
IPv6 Dropped Frame Count. Type: u64 Default: 0 |
| Ipv6IntendedBpsLoad |
IPv6 Intended Load in bps. Type: double Default: 0 |
| Ipv6IntendedFPSLoad |
IPv6 Intended Load in Frames Per Second. Type: double Default: 0 |
| Ipv6IntendedIBGLoad |
IPv6 Intended Load in Inter Burst gap. Type: double Default: 0 |
| Ipv6IntendedKbpsLoad |
IPv6 Intended Load in Kbps. Type: double Default: 0 |
| Ipv6IntendedLoad |
IPv6 Intended Load. Type: double Default: 0 |
| Ipv6IntendedMbpsLoad |
IPv6 Intended Load in Mbps. Type: double Default: 0 |
| Ipv6IntendedPCTLoad |
IPv6 Intended Load in percent. Type: double Default: 0 |
| Ipv6Ipv4CoexistenceRatio |
IPv6-IPv4 Coexistence Ratio. Type: string Default: N/A |
| Ipv6MaxJitter |
IPv6 Maximum Jitter (us). Type: double Default: 0 |
| Ipv6MaxLatency |
IPv6 Maximum Latency (us). Type: double Default: 0 |
| Ipv6MinJitter |
IPv6 Minimum Jitter (us). Type: double Default: 0 |
| Ipv6MinLatency |
IPv6 Minimum Latency (us). Type: double Default: 0 |
| Ipv6OfferedBpsLoad |
IPv6 Offered Load in bps. Type: double Default: 0 |
| Ipv6OfferedFPSLoad |
IPv6 Offered Load in Frames Per Second. Type: double Default: 0 |
| Ipv6OfferedIBGLoad |
IPv6 Offered Load in Inter Burst gap. Type: double Default: 0 |
| Ipv6OfferedKbpsLoad |
IPv6 Offered Load in Kbps. Type: double Default: 0 |
| Ipv6OfferedLoad |
IPv6 Offered Load. Type: double Default: 0 |
| Ipv6OfferedMbpsLoad |
IPv6 Offered Load in Mbps. Type: double Default: 0 |
| Ipv6OfferedPCTLoad |
IPv6 Offered Load in percent. Type: double Default: 0 |
| Ipv6RxFrameCount |
IPv6 Rx Frame Count. Type: u64 Default: 0 |
| Ipv6TxFrameCount |
IPv6 Tx Frame Count. Type: u64 Default: 0 |
| Ipv6TxFrameRate |
IPv6 Tx Frame Rate. Type: double Default: 0 |
| IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Trial Number. Type: u8 Default: 0 |
| LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Load Size. Type: double Default: 0 |
| LoadSizeType |
Load Size Type. Type: string Default: 0 |
| MaxJitter |
Maximum Jitter (us). Type: double Default: 0 |
| MaxLatency |
Maximum Latency (us). Type: double Default: 0 |
| MaxReceiveRate |
Maximum Receive Rate in bps. Type: double Default: 0 |
| MaxSendRate |
Maximum Send Rate in bps. Type: double Default: 0 |
| MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Tx Rate (Mbps). Type: double Default: 0 |
| MinJitter |
Minimum Jitter (us). Type: double Default: 0 |
| MinLatency |
Minimum Latency (us). Type: double Default: 0 |
| MinReceiveRate |
Minimum Receive Rate in bps. Type: double Default: 0 |
| MinSendRate |
Minimum Send Rate in bps. Type: double Default: 0 |
| NumEgressPorts |
Number of Egress Ports. Type: u32 Default: 0 |
| NumIngressPorts |
Number of Ingress Ports. Type: u32 Default: 0 |
| OfferedBpsLoad |
Offered Load in bps. Type: double Default: 0 |
| OfferedFPSLoad |
Offered Load in Frames Per Second. Type: double Default: 0 |
| OfferedIBGLoad |
Offered Load in Inter Burst gap. Type: double Default: 0 |
| OfferedKbpsLoad |
Offered Load in Kbps. Type: double Default: 0 |
| OfferedLoad |
Offered Load. Type: double Default: 0 |
| OfferedMbpsLoad |
Offered Load in Mbps. Type: double Default: 0 |
| OfferedPCTLoad |
Offered Load in percent. Type: double Default: 0 |
| OtherFrameCount |
Other Received Frame Count. Type: u64 Default: 0 |
| OutOfSeqCount |
Out of Sequence Count. Type: u64 Default: 0 |
| PauseFrameCount |
Rx Pause Frame Count. Type: u64 Default: 0 |
| PayloadSize |
Payload Size. Type: double Default: 0 |
| PercentLoss |
Dropped Frame Percent. Type: double Default: 0 |
| PfcFrameCount |
Rx PFC Frame Count. Type: u64 Default: 0 |
| PortType |
TCP or UDP. Type: string Default: 0 |
| QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
| ReceiveRate |
Receive Rate in bps. Type: double Default: 0 |
| RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rx Expected Frame Count. Type: u64 Default: 0 |
| RxFrameCount |
Rx Frame Count. Type: u64 Default: 0 |
| RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rx Non Signature Frame Count. Type: u64 Default: 0 |
| RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rx Signature Frame Count. Type: u64 Default: 0 |
| SendRate |
Send Rate in bps. Type: double Default: 0 |
| TrialNum |
Trial Number. Type: u8 Default: 0 |
| TxFrameCount |
Tx Frame Count. Type: u64 Default: 0 |
| TxFrameRate |
Tx Frame Rate. Type: double Default: 0 |
| TxMbpsLoad |
Layer 1 Tx Rate (Mbps). Type: double Default: 0 |
| TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Tx Signature Frame Count. Type: u64 Default: 0 |