Description:
Service Config Summary Results
Parents: Project
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
ResultParent (ResultChild) |
Use this to connect a results object to an object. |
Attribute | Description | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
Read-Only Attribute | Description |
---|---|
AvgJitter |
Average Jitter (us) Type: double Default: 0 |
AvgLatency |
Average Latency (us) Type: double Default: 0 |
BurstSize |
Burst Size Type: u64 Default: 0 |
Cbs |
Committed Burst Size Type: double Default: 0 |
ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
Cir |
Committed Information Rate of the CIR Sub Test Type: double Default: 0 |
Color |
If the test contains green or yellow frames Type: string Default: "" (empty string) |
ConfiguredFrameSize |
Configured Tx Frame Size Type: double Default: 0 |
DstIpv4 |
Destination Ipv4 Address Type: string Default: "" (empty string) |
DstIpv6 |
Destination Ipv6 Address Type: string Default: "" (empty string) |
DstMac |
Destination MAC Encapsulation Type: string Default: "" (empty string) |
DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
Duration |
Duration of the sub-test Type: u64 Default: 0 |
Ebs |
Excess Burst Size Type: double Default: 0 |
Eir |
Excess Information Rate Type: double Default: 0 |
EmixFrameSizes |
List of EMIX frame sizes Type: string Default: "" (empty string) |
ExpectedFdv |
Expected Frame Delay Variation Type: double Default: 0 |
ExpectedFlr |
Expected Frame Loss Ratio Type: double Default: 0 |
ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
ExpectedFtd |
Expected Frame Transfer Delay Type: double Default: 0 |
FailureReason |
Reason for the test failure Type: string Default: "" (empty string) |
FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
Fdv |
Frame Delay Variation Type: double Default: 0 |
Fl |
Frame Loss Type: double Default: 0 |
FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
Flr |
Frame Loss Ratio Type: double Default: 0 |
ForwardingRate |
Forwarding Rate (fps) Type: double Default: 0 |
FrameLengthDistribution |
iMIX Distribution Type: string Default: N/A |
FrameLoss |
Total number of test frames expected, but not received during the test. Type: u64 Default: 0 |
FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
FrameSize |
Average Tx Frame Size Type: double Default: 0 |
FrameSizeType |
Frame Size Type Type: string Default: 0 |
Ftd |
Frame Transfer Delay Type: double Default: 0 |
InfoRate |
Information Rate received from IL Type: double Default: 0 |
IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
IntendedLoad |
Intended Load Type: double Default: 0 |
IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
IterationNum |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Trial Number Type: u8 Default: 0 |
LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load value. Type: double Default: 0 |
LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
MaxFdv |
Maximum Frame Delay Variation Type: double Default: 0 |
MaxFtd |
Maximum Frame Transfer Delay Type: double Default: 0 |
MaxJitter |
Maximum Jitter (us) Type: double Default: 0 |
MaxLatency |
Maximum Latency (us) Type: double Default: 0 |
MbpsLineRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Tx Rate (Mbps) Type: double Default: 0 |
MeanFdv |
Mean Frame Delay Variation Type: double Default: 0 |
MeanFtd |
Mean Frame Transfer Delay Type: double Default: 0 |
MeshType |
Mesh type for the test Type: string Default: "" (empty string) |
MinFdv |
Minimum Frame Delay Variation Type: double Default: 0 |
MinFtd |
Minimum Frame Transfer Delay Type: double Default: 0 |
MinJitter |
Minimum Jitter (us) Type: double Default: 0 |
MinLatency |
Minimum Latency (us) Type: double Default: 0 |
OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
OutOfSeqCount |
Out of Sequence Count Type: u64 Default: 0 |
PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
PercentLoss |
Percentage of test frames that were expected, but not received. Type: double Default: 0 |
PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
Result |
Result of the test either Passed or Failed Type: string Default: "" (empty string) |
RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
RxFrameCount |
Received frame count. Type: u64 Default: 0 |
RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
ServiceBlockName |
Service Name Type: string Default: "" (empty string) |
ServiceName |
Service Name Type: string Default: "" (empty string) |
ServiceNameOrder |
Service Name Order Type: string Default: "" (empty string) |
SrcIpv4 |
Source Ipv4 Address Type: string Default: "" (empty string) |
SrcIpv6 |
Source Ipv6 Address Type: string Default: "" (empty string) |
SrcMac |
Source Mac Encapsulation Type: string Default: "" (empty string) |
Step |
CIR Step size Type: u64 Default: 0 |
StreamBlockHandle |
Handle of the Stream Block Type: handle Default: 0 |
StreamIndex |
Index within Stream Type: u64 Default: 0 |
SubTestType |
Sub Test Type Type: string Default: "" (empty string) |
TrafficType |
Traffic type for the test Type: string Default: "" (empty string) |
TrialNum |
Trial Number Type: u8 Default: 0 |
TxFrameCount |
Transmitted frame count. Type: u64 Default: 0 |
TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
TxMbpsLoad |
Layer 1 Tx Rate (Mbps) Type: double Default: 0 |
TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |
Vlan1Id |
VLAN 1 ID Type: string Default: "" (empty string) |
Vlan2Id |
VLAN 2 ID Type: string Default: "" (empty string) |