Description:
Y.1564 Test Result
Parents: Project
Attribute | Description | ||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
DisplayLoadUnit |
Display units for load in results. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
Read-Only Attribute | Description |
---|---|
BurstSize |
Burst Size. Type: u64 Default: 0 |
ChecksumErrorCount |
Total number of IP/UDP/TCP checksum errors received during the test. Type: u64 Default: 0 |
ConfiguredFrameSize |
Configured Tx Frame Size. Type: double Default: 0 |
DuplicateFrameCount |
Minimum number of duplicate frames received during a test run. This number may not be accurate due to the analyzer mode used for the RFC 2544/2889 tests. Type: u64 Default: 0 |
ExpectedFrameCount |
Total number of test frames that were expected to be received. Type: u64 Default: 0 |
FcsErrorFrameCount |
Total number of frame check sequence errors received during the test. Type: u64 Default: 0 |
FloodCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
FloodedFrameCount |
Total number of test frames flooded to the incorrect egress port during the test. Type: u64 Default: 0 |
FrameLengthDistribution |
iMIX Distribution. Type: string Default: N/A |
FrameLoss |
Total number of test frames expected, but not received during the test. Type: u64 Default: 0 |
FrameRate |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Rate at which frames are transmitted. Type: double Default: 0 |
FrameSize |
Average Tx Frame Size. Type: double Default: 0 |
FrameSizeType |
Frame Size Type. Type: string Default: 0 |
IntendedBpsLoad |
Intended load rate in bits per second. Type: double Default: 0 |
IntendedFPSLoad |
Intended load in frames per second. Type: double Default: 0 |
IntendedIBGLoad |
Intended load rate in inter burst gaps. Type: double Default: 0 |
IntendedKbpsLoad |
Intended load rate in kilobits per second. Type: double Default: 0 |
IntendedLoad |
Intended Load. Type: double Default: 0 |
IntendedMbpsLoad |
Intended load rate in megabits per second. Type: double Default: 0 |
IntendedPCTLoad |
Intended load rate in percentage. Type: double Default: 0 |
IterationTotal |
Total Number of Iterations. Type: u8 Default: 0 |
LoadSize |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Traffic load value. Type: double Default: 0 |
LoadSizeType |
Specifies how the traffic load was configured. Can be Fixed or Random. Type: string Default: 0 |
OfferedBpsLoad |
Offered load rate in bits per second. Type: double Default: 0 |
OfferedFPSLoad |
Offered load in frames per second. Type: double Default: 0 |
OfferedIBGLoad |
Offered load in inter burst gaps. Type: double Default: 0 |
OfferedKbpsLoad |
Offered load rate in Kilobit per second. Type: double Default: 0 |
OfferedLoad |
Load (in percent or frames per second) offered by the DUT. Type: double Default: 0 |
OfferedMbpsLoad |
Offered load rate in megabits per second. Type: double Default: 0 |
OfferedPCTLoad |
Offered load rate in percentage. Type: double Default: 0 |
OtherFrameCount |
Total number of non-test traffic frames received during the test. Type: u64 Default: 0 |
PauseFrameCount |
Total number of pause frames received by the test ports during the test. Type: u64 Default: 0 |
PercentLoss |
Percentage of test frames that were expected, but not received. Type: double Default: 0 |
PfcFrameCount |
Number of PFC frames received. Type: u64 Default: 0 |
QueuePair |
Queue Pair on RoCEv2 stream Type: double Default: 0 |
RxExpectedFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames expected during a test. Type: u64 Default: 0 |
RxFrameCount |
Received frame count. Type: u64 Default: 0 |
RxNonSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of non-signature test frames received during a test. Type: u64 Default: 0 |
RxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames received during a test. Type: u64 Default: 0 |
TxFrameCount |
Transmitted frame count. Type: u64 Default: 0 |
TxFrameRate |
Intended frame rate (ILoad) for the test. Type: double Default: 0 |
TxSigFrameCount |
NOTE: This attribute is deprecated. It will be removed in subsequent releases, so it is recommended that you do not use it. Total number of signature frames transmitted during a test. Type: u64 Default: 0 |