Rfc2889SetupCongestionControlTestCommand Object

HOME | TECHNOLOGIES | TEST CONFIGURATION | SEQUENCER COMMANDS | GUI COMMAND NAMES | ALL COMMANDS | RESULT | PDU | ALL | OBJECT TREE

Description:

Set up RFC 2889 congestion control test.

Can be used with Command Sequencer: No

Parents: Sequencer

Relations:

Side name
(Type)		 Relative Description
TestCaseConfig
(BenchmarkingTestCaseConfig)

DcbTestConfig, Rfc2544BackToBackFramesConfig, Rfc2544FrameLossConfig, Rfc2544LatencyConfig, Rfc2544ThroughputConfig, Rfc2544TrafficGroupConfig, Rfc2889AddrCachingCapacityConfig, Rfc2889AddrLearningRateConfig, Rfc2889BroadcastFrameForwardingConfig, Rfc2889BroadcastFrameLatencyConfig, Rfc2889CongestionControlConfig, Rfc2889ErroredFramesFilteringConfig, Rfc2889ForwardingConfig, Rfc2889ForwardPressureConfig, Rfc2889MaxForwardingRateConfig, Rfc3918Config, Rfc5180Config

Benchmarking test case config used to set up test command.
SequencerRootCommand
(BenchmarkingTestCaseRootCommand)

SequencerGroupCommand

Parent command.

Rfc2889SetupCongestionControlTestCommand Writable Attributes

Attribute Description
BurstSizeList

Burst size list.

Type: u32

Default: 0

Range: 1 - 4294967295
DstDeviceList

Destination device list.

Type: handle

Default: 0
Duration

Transmission time in seconds.

Type: double

Default: 60

Range: 1 - 16777215
DurationMode

Duration mode for each transmitted stream. Whether to measure test duration in seconds or number of frames.

Type: enum

Default: SECONDS

Possible Values:

Value Description
SECONDS

Sets duration mode to time in seconds.
BURSTS

Sets duration mode to number of frames per transmission burst.
FrameSizeList

Frame size list.

Type: u16

Default: 0

Range: 47 - 16383
LatencyType

How latency results are calculated and displayed.

Type: enum

Default: LILO

Possible Values:

Value Description
FIFO

First In First Out mode.
LIFO

Last In First Out mode.
LILO

Last In Last Out mode.
FILO

Firt in, last out mode.
LearningFreqMode

Learning frequency.

Type: enum

Default: LEARN_ONCE

Possible Values:

Value Description
NONE

No learning.
LEARN_ONCE

Learn once per test.
LEARN_EVERY_TRIAL

Learn every trial.
LEARN_EVERY_FRAME_SIZE

Learn every frame size.
LEARN_EVERY_ITERATION

Learn every iteration.
LoadList

List of user defined load values.

Type: double

Default: 0

Range: 0.000001 - 100000.0
LoadUnits

Unit of measurement for the load parameter, applied to all ports and streams in the test.

Type: enum

Default: PERCENT_LINE_RATE

Possible Values:

Value Description
PERCENT_LINE_RATE

Load expressed in a percentage.
FRAMES_PER_SECOND

Load expressed in frames per second.
MEGABITS_PER_SECOND

Load expressed by megabits per second.
KILOBITS_PER_SECOND

Load expressed by kilobits per second.
BITS_PER_SECOND

Load expressed by bits per second.
NumOfTrials

Number of trials.

Type: u16

Default: 1

Range: 1 - 60
SrcDeviceList

Source device list.

Type: handle

Default: 0
TrafficVerificationAbortOnFail

Test behavior when traffic verification fails.

Type: bool

Default: TRUE

Possible Values:

Value Description
TRUE

Abort the test and set the sequencer status mode to FAIL if traffic verification is not successful.
FALSE

Do nothing. Test continues without interruption.
TrafficVerificationFreqMode

Specifies when to perform traffic verification during the test.

Type: enum

Default: NONE

Possible Values:

Value Description
NONE

No verification.
VERIFY_EVERY_TRIAL

Verify traffic forwarding at the beginning of every trial.
VERIFY_EVERY_FRAME_SIZE

Verify traffic forwarding after changing the frame size.
VERIFY_EVERY_ITERATION

Verify traffic forwarding at the beginning of every iteration.
TrafficVerificationTxFrameCount

Number of frames to use for traffic verification.

Type: u32

Default: 100

Range: 1 - 32767
TrafficVerificationTxFrameRate

Number of frames to use for traffic verification.

Type: u32

Default: 1000

Range: 1 - 14880952

Rfc2889SetupCongestionControlTestCommand Read-Only Attributes

There are no read-only attributes.