Description:
Set up RFC 3918 multicast group capacity test.
Can be used with Command Sequencer: No
Parents: Sequencer
Relations:
Side name (Type) |
Relative | Description |
---|---|---|
TestCaseConfig (BenchmarkingTestCaseConfig) |
DcbTestConfig, Rfc2544BackToBackFramesConfig, Rfc2544FrameLossConfig, Rfc2544LatencyConfig, Rfc2544ThroughputConfig, Rfc2544TrafficGroupConfig, Rfc2889AddrCachingCapacityConfig, Rfc2889AddrLearningRateConfig, Rfc2889BroadcastFrameForwardingConfig, Rfc2889BroadcastFrameLatencyConfig, Rfc2889CongestionControlConfig, Rfc2889ErroredFramesFilteringConfig, Rfc2889ForwardingConfig, Rfc2889ForwardPressureConfig, Rfc2889MaxForwardingRateConfig, Rfc3918Config, Rfc5180Config |
Benchmarking test case config used to set up test command. |
SequencerRootCommand (BenchmarkingTestCaseRootCommand) |
Parent command. |
Attribute | Description | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Backoff |
Rate at which the load decreases after the DUT fails at the current load. Applicable when SearchMode is BINARY or COMBO. Type: double Default: 50.0 Range: 0.001 - 99.999 |
||||||||||||
DstDeviceList |
Destination device list. Type: handle Default: 0 |
||||||||||||
Duration |
Transmission time in seconds. Type: double Default: 60 Range: 1 - 16777215 |
||||||||||||
DurationMode |
Duration mode for each transmitted stream. Whether to measure test duration in seconds or number of frames. Type: enum Default: SECONDS Possible Values:
|
||||||||||||
GroupSearchInitial |
Initial group count for binary search. Type: u32 Default: 10 Range: 1 - 2147483646 |
||||||||||||
GroupSearchLowerLimit |
Lower limit for group search. Type: u32 Default: 10 Range: 1 - 2147483646 |
||||||||||||
GroupSearchMode |
Mode for the group search. Type: enum Default: BINARY Possible Values:
|
||||||||||||
GroupSearchStep |
Group count step for step search. Type: u32 Default: 10 Range: 1 - 2147483646 |
||||||||||||
GroupSearchUpperLimit |
Upper limit for group search. Type: u32 Default: 100 Range: 2 - 2147483646 |
||||||||||||
L4HeaderType |
L4 Header Type. Type: enum Default: UDP Possible Values:
|
||||||||||||
LatencyType |
How latency results are calculated and displayed. Type: enum Default: LILO Possible Values:
|
||||||||||||
LearningFreqMode |
Learning frequency. Type: enum Default: LEARN_EVERY_TOPOLOGY_CHANGE Possible Values:
|
||||||||||||
MonitorPortList |
List of ports acting as monitor ports for test. Type: handle Default: 0 |
||||||||||||
MulticastClientVersion |
Protocol to use for multicast clients. Type: enum Default: IGMP_V2 Possible Values:
|
||||||||||||
MulticastFrameSizeDistributionList |
List of iMIX distributions. Type: handle Default: 0 |
||||||||||||
MulticastFrameSizeList |
Multicast frame size list. Type: u16 Default: 0 Range: 47 - 16383 |
||||||||||||
MulticastGroupIpAddrBase |
IP Multicast group base address. Type: ip Default: 225.0.0.1 |
||||||||||||
MulticastGroupIpAddrPortStep |
IP Multicast group port step value. Type: ip Default: 0.1.0.0 |
||||||||||||
MulticastGroupIpAddrStep |
IP Multicast address step. Type: u32 Default: 2 Range: 1 - 4294967295 |
||||||||||||
MulticastGroupIpv6AddrBase |
IPv6 Multicast group base address. Type: ipv6 Default: ff1e::1 |
||||||||||||
MulticastGroupIpv6AddrPortStep |
IPv6 Multicast group port step value. Type: ipv6 Default: 0:0:0:1::0 |
||||||||||||
MulticastGroupIpv6AddrStep |
IPv6 Multicast group step value. Type: u32 Default: 2 Range: 1 - 4294967295 |
||||||||||||
MulticastLoadList |
List of user defined load values. Type: double Default: 0 Range: 0.000001 - 100000.0 |
||||||||||||
MulticastLoadUnits |
Multicast load units. Type: enum Default: PERCENT_LINE_RATE Possible Values:
|
||||||||||||
MulticastTrafficList |
Traffic list. Type: handle Default: 0 |
||||||||||||
MulticastTrafficPattern |
Traffic pattern type. Type: enum Default: BACKBONE Possible Values:
|
||||||||||||
NumOfTrials |
Number of trials. Type: u16 Default: 1 Range: 1 - 60 |
||||||||||||
Resolution |
Finest adjustment possible for the load from iteration to iteration. If the required adjustment to the current load for the next iteration is less than the resolution, the search stops. Applicable when SearchMode is BINARY or COMBO. Type: u32 Default: 10 Range: 1 - 1000 |
||||||||||||
SrcDeviceList |
Source device list. Type: handle Default: 0 |
||||||||||||
TrafficVerificationAbortOnFail |
Test behavior when traffic verification fails. Type: bool Default: TRUE Possible Values:
|
||||||||||||
TrafficVerificationFreqMode |
Specifies when to perform traffic verification during the test. Type: enum Default: NONE Possible Values:
|
||||||||||||
TrafficVerificationTxFrameCount |
Number of frames to use for traffic verification. Type: u32 Default: 100 Range: 1 - 32767 |
||||||||||||
TrafficVerificationTxFrameRate |
Traffic rate in frames per second to use for traffic verification. Type: u32 Default: 1000 Range: 1 - 14880952 |
There are no read-only attributes.