PppoeServerBlockConfig Object

ViewControlPlaneMplsBindingResult

Relates the MPLS control plane binding result to PppoeServerBlockConfig object.

ConvergenceConfig, ConvergenceConfig

Primary convergence config.

PppClientBlockResults, PppoaClientBlockResults, PppoaServerBlockResults, PppoeClientBlockResults, PppoePortResults, PppoeServerBlockResults, PppoeServerBlockResults, PppServerBlockResults

Use this to connect a results object to an object.

TsnProtocolsTimeComparisonPair, TsnProtocolsTimeComparisonPair

Aal5If, EthIIIf, FcIf, GreIf, GroupIf, HdlcIf, Ipv4If, Ipv6If, Ipv6SrhIf, ItagIf, L2tpv2If, L2tpv3If, LispIf, MacsecIf, MplsIf, PppIf, PppoeIf, TrillIf, VbrasIf, VlanIf, VxlanGpeIf, VxlanIf

Specifies the interfaces used by the configuration object (configuration object examples: BgpRouterConfig, LdpRouterConfig, and so on).

Set the Access Concentrator name in the PADO messages.

Type: string

Default: SpirentTestCenter

Range: 1 - 64 characters

Type of authentication to use.

Type: enum

Default: NONE

Possible Values:

The file path of imported authentication list.

Type: inputFilePath

Default: "" (empty string)

Enable automatically calculate MRU(Spirent TestCenter negotiate the MRU in LCP).

Type: bool

Default: FALSE

Possible Values:

Timeout wait period for peer to send CHAP response.

Type: u16

Default: 3

Range: 1 - 65535

Enabled for DSL-type relay agents only. The circuit ID can be used to encode a local identifier for the circuit that received a PPP packet from a client, destined for the access concentrator. Not applicable for the PPPoX server mode.

Type: string

Default: circuit @s

Range: 0 - 255 characters

Maximum rate in the number of session per second at which session will be connected for a PPPoX device block.

Type: u16

Default: 100

Range: 1 - 1000

Maximum rate in the number of sessions per second at which sessions will be disconnected for a PPPoX device block.

Type: u16

Default: 100

Range: 1 - 1000

Interval in seconds between sending out consecutive echo requests.

Type: u16

Default: 10

Range: 0 - 65535

Whether to include the Vendor-Specific Tag in the PADO.

Type: bool

Default: FALSE

Possible Values:

Whether to include the Vendor-Specific Tag in the PADS.

Type: bool

Default: FALSE

Possible Values:

Always Enable Address and Control field

Type: bool

Default: FALSE

Possible Values:

Enables Auto Fill for the IPv6 address through transmission/receipt of RS/RA messages to the DUT.

Type: bool

Default: TRUE

Possible Values:

Enable echo requests.

Type: bool

Default: FALSE

Possible Values:

Whether to allow the server to be forced into CONNECTED state without having all of its sessions connected.

Type: bool

Default: FALSE

Possible Values:

Enable or disable Magic Number negotiation.

Type: bool

Default: TRUE

Possible Values:

Enable or disable the PPP-Max-Payload-Tag (see RFC 4638).

Type: bool

Default: FALSE

Possible Values:

For PPPoPOS, enable MPLS option.

Type: bool

Default: FALSE

Possible Values:

Enable or disable MRU negotiation.

Type: bool

Default: TRUE

Possible Values:

Terminate the session from NCP.

Type: bool

Default: FALSE

Possible Values:

For PPPoPOS, enable OSI NLCP option.

Type: bool

Default: FALSE

Possible Values:

Enable password validation

Type: bool

Default: FALSE

Possible Values:

Enable Primary DNS

Type: bool

Default: TRUE

Possible Values:

Enable or disable the relay agent.

Type: bool

Default: FALSE

Possible Values:

Enable Secondary DNS

Type: bool

Default: TRUE

Possible Values:

Enable LCP vendor specific packet

Type: bool

Default: FALSE

Possible Values:

Expected peer MRU size

Type: u16

Default: 1492

Range: 128 - 65535

Include the relay agent tags in transmitted PADI messages. Not applicable for the PPPoX server mode.

Type: bool

Default: TRUE

Possible Values:

Include the relay agent tags in transmitted PADR messages. Not applicable for the PPPoX server mode.

Type: bool

Default: TRUE

Possible Values:

Include or exclude the Identifier field of the Challenge message.

Type: bool

Default: TRUE

Possible Values:

Enable IPv6CP or IPv4CP. Must have at least one enabled.

Type: enum

Default: IPV4

Possible Values:

Maximum number of configure requests that can be sent, without acknowledgment, before a session fails.

Type: u16

Default: 10

Range: 1 - 65535

Timeout value in seconds for acknowledgment of a configure request.

Type: u16

Default: 3

Range: 1 - 65535

Maximum number of terminate requests that can be sent, without acknowledgment, before a session fails.

Type: u16

Default: 10

Range: 1 - 65535

Timeout value in seconds for acknowledgment of a terminate request.

Type: u16

Default: 3

Range: 1 - 65535

PPP LCP vendor specific kind

Type: u8

Default: 0

PPP LCP vendor specific Value

Type: string

Default: "" (empty string)

Maximum CHAP challenge attempts.

Type: u16

Default: 10

Range: 1 - 65535

Number of consecutive, unanswered echo requests to send before failing the subscriber session.

Type: u16

Default: 1

Range: 0 - 65535

Maximum Negative-Acknowledgments allowed during LCP and NCP configuration/negotiation.

Type: u16

Default: 5

Range: 1 - 65535

Maximum number of PPP payload bytes the client can transmit and receive. This value will be used in the PPP-Max-Payload tag in PPPoE Active Discovery Initialized (PADI) and PPPoE Active Discovery Request (PADR) messages.

Type: u16

Default: 1500

Range: 0 - 65535

Local maximum receive unit (MRU) size in bytes.

Type: u16

Default: 1492

Range: 128 - 65535

Maximum number of NCP Configure-Requests that can be sent, without acknowledgment, before a session fails.

Type: u16

Default: 10

Range: 1 - 65535

Timeout value in seconds for acknowledgment of an NCP Configure-Request.

Type: u16

Default: 3

Range: 1 - 65535

Timeout wait period for PAP request Rx from peer.

Type: u16

Default: 3

Range: 1 - 65535

Password for authenticated PPP sessions. Use wildcard characters to make each password unique:

@s - Session index associated with the PPPoX client.

@b - Block (host/router) index.

@p - Port name.

@m - MAC address of the PPPoX client.

@x - Custom step setup in (start,count,step,zeropadding,stutter) format.

start - starting value.

count - number of values to generate.

step - amount to increment the start value when the start value must be stepped.

zeropadding - length the value should be padded to by prepending 0's.

stutter - number of times a value should be repeated before applying the step.

@@ - This must be used to include the textual "@" symbol in the string.

Type: string

Default: spirent

Range: 1 - 64 characters

Primary DNS

Type: ip

Default: null

Type of PPP session.

Type: enum

Default: UNDEFINED

Possible Values:

M and O flags for Router Advertisement.

Type: enum

Default: NODHCP

Possible Values:

Enabled for RFC 2516-type relay agents only. The Relay Agent MAC address is the MAC address of the next hop from the subscriber client group to the access concentrator. Not applicable for the PPPoX server mode.

Type: mac

Default: 00-00-00-00-00-00

Increment value to create Relay Agent Destination MAC Address.

Type: mac

Default: 00-00-00-00-00-01

Select the type of relay agent. Not applicable for the PPPoX server mode.

Type: enum

Default: RFC_2516

Possible Values:

Remote ID or Session ID depending on the Relay Agent type. Not applicable for the PPPoX server mode.

Type: string

Default: remote @m-@p-@b

Range: 0 - 255 characters

Secondary DNS

Type: ip

Default: null

Number of seconds to wait before the server is forced into a connected state. Timer begins when the maximum number of unconnected sessions is met. It is reset upon receipt of a packet on the server (excluding keepalives). When the timer expires, the server is put into the connected state.

Type: u16

Default: 30

Range: 1 - 65535

Service that will be connected per RFC 2516. If the cell is left blank, any service is acceptable.

Type: string

Default: "" (empty string)

Range: 0 - 255 characters

Number of clients.

Type: u32

Default: 65535

Range: 0 - 65535

Maximum number of unconnected sessions allowed before a PPPoX server is forced into connected state.

Type: u16

Default: 0

Range: 0 - 65535

Use imported authentication list file or not.

Type: bool

Default: FALSE

Possible Values:

Whether to use partial block state.

Type: bool

Default: FALSE

Possible Values:

User name for authenticated PPP sessions. Use wildcard characters to make each user name unique:

@s - Session index associated with the PPPoX client.

@b - Block (host/router) index.

@p - Port name.

@m - MAC address of the PPPoX client.

@x - Custom step setup in (start,count,step,zeropadding,stutter) format.

start - starting value.

count - number of values to generate.

step - amount to increment the start value when the start value must be stepped.

zeropadding - length the value should be padded to by prepending 0's.

stutter - number of times a value should be repeated before applying the step.

@@ - This must be used to include the textual "@" symbol in the string.

Type: string

Default: spirent

Range: 1 - 64 characters

State of the server block.

Type: enum

Default: NONE

Possible Values:

IPv4 NCP block state.

Type: enum

Default: NONE

Possible Values:

IPv6 NCP block state.

Type: enum

Default: NONE

Possible Values:

Whether this node is a server or not.

Type: bool

Default: FALSE

Possible Values: