VLAN interface object.
Side name
(Type) |
Relative |
Description |
GroupIf (AffiliatedGroupIf) |
GroupIf
|
Affiliated group interface.
|
DstBoundTo (DstBinding) |
PathDescriptor, StreamBlock, TrafficDescriptor
|
Specifies destination endpoints bound to StreamBlock.
|
EncapsulationSource (Encapsulation) |
PathDescriptor
|
Specifies the encapsulation.
|
NetworkLink (LinkSrc) |
CustomLink, CustomLink, DualStackLiteLink, DualStackLiteLink, EoamLink, EoamLink, EthernetBridgeLink, EthernetBridgeLink, EvpnCeToPeLink, EvpnCeToPeLink, IpForwardingLink, IpForwardingLink, Ipv6RapidDeploymentLink, Ipv6RapidDeploymentLink, ItagServiceLink, ItagServiceLink, L2GreTunnelLink, L2GreTunnelLink, L2tpv3ForwardingLink, L2tpv3ForwardingLink, MplsForwardingLink, MplsForwardingLink, MplsHierarchicalLink, MplsHierarchicalLink, MplsIpv4VpnCeToPeLink, MplsIpv4VpnCeToPeLink, MplsIpv6VpnCeToPeLink, MplsIpv6VpnCeToPeLink, MplsL2VpnPeToPLink, MplsL2VpnPeToPLink, MplsL3VpnPeToPLink, MplsL3VpnPeToPLink, MVpnGreCeToPeLink, MVpnGreCeToPeLink, MVpnGrePeToPLink, MVpnGrePeToPLink, OtvEdgeDeviceLink, OtvEdgeDeviceLink, StationToScompLink, StationToScompLink, VifToVicLink, VifToVicLink, VlanSwitchLink, VlanSwitchLink, VplsBgpCeToPeLink, VplsBgpCeToPeLink, VplsLdpCeToPeLink, VplsLdpCeToPeLink, VsiToStationLink, VsiToStationLink, VxlanGpeLink, VxlanGpeLink, VxlanVmToVtepLink, VxlanVmToVtepLink
|
Link source.
|
MemberOfVpn (MemberOfVpn) |
EthernetVpnSiteInfo, VpnIdGroup, VpnSiteInfo6Pe, VpnSiteInfoMplsTpStatic, VpnSiteInfoRfc2547, VpnSiteInfoRfc4659, VpnSiteInfoVplsBgp, VpnSiteInfoVplsLdp
|
Do not use, to be removed
|
MulticastExpectedRxPorts (MulticastExpectedRxPorts) |
Port
|
Traffic sent to this end point is expected to be received as multicast traffic by
any of the ports connected through this relation.
|
OptionallyStackedUnder (OptionallyStackedOnEndpoint) |
Aal5If, Dhcpv4ServerDefaultPoolConfig, Dhcpv4ServerPoolConfig, Dhcpv6ServerAddrPoolConfig, Dhcpv6ServerDefaultAddrPoolConfig, Dhcpv6ServerDefaultPrefixPoolConfig, Dhcpv6ServerPrefixPoolConfig, EthIIIf, FcIf, GreIf, GroupIf, HdlcIf, Ipv4If, Ipv4NetworkBlock, Ipv4VpnMcastNetworkBlock, Ipv6If, Ipv6NetworkBlock, Ipv6SrhIf, Ipv6VpnMcastNetworkBlock, ItagIf, L2tpv2If, L2tpv3If, LispIf, MacBlock, MacsecIf, MplsIf, Pimv4JoinSrc, Pimv4PruneSrc, Pimv6JoinSrc, Pimv6PruneSrc, PppIf, PppoeIf, PppoeServerIpv4PeerPool, PppoxServerIpv4PeerPool, PppoxServerIpv6PeerPool, TrillIf, VbrasIf, VlanBlock, VlanIf, VxlanGpeIf, VxlanIf
|
Specifies an optionally-selected lower interface in the stack. Selection is
controlled by protocol implementations which decide based on other criteria whether they
should include the target interface in their stack.
|
OtvEdgeDeviceConfig (OtvTopLevelIf) |
OtvEdgeDeviceConfig
|
OTV top level private interface.
|
PrimaryIfSource (PrimaryIf) |
EmulatedDevice, ExternalDevice, ExternalDevicePort, Host, Port, Router, SUT
|
Specifies if a top-level interface is facing the DUT.
|
RelayBlockConfig (RelayIf) |
Dhcpv4BlockConfig, Dhcpv4BlockConfig
|
Config to relay agent interface.
|
(ResolvesInterface) |
BgpRouterConfig, IsisRouterConfig, LdpRouterConfig, LispRouterConfig, Ospfv2RouterConfig, Ospfv3RouterConfig, RsvpIngressTunnelParams, RsvpRouterConfig
|
Use this to link the traffic binding interfaces and traffic binding
resolver.
|
SrcBoundTo (SrcBinding) |
PathDescriptor, StreamBlock, TrafficDescriptor
|
Specifies the source endpoint bound to StreamBlock.
|
StackedOn (StackedOnEndpoint) |
Aal5If, Dhcpv4ServerDefaultPoolConfig, Dhcpv4ServerPoolConfig, Dhcpv6ServerAddrPoolConfig, Dhcpv6ServerDefaultAddrPoolConfig, Dhcpv6ServerDefaultPrefixPoolConfig, Dhcpv6ServerPrefixPoolConfig, EthIIIf, FcIf, GreIf, GroupIf, HdlcIf, Ipv4If, Ipv4NetworkBlock, Ipv4VpnMcastNetworkBlock, Ipv6If, Ipv6NetworkBlock, Ipv6SrhIf, Ipv6VpnMcastNetworkBlock, ItagIf, L2tpv2If, L2tpv3If, LispIf, MacBlock, MacsecIf, MplsIf, Pimv4JoinSrc, Pimv4PruneSrc, Pimv6JoinSrc, Pimv6PruneSrc, PppIf, PppoeIf, PppoeServerIpv4PeerPool, PppoxServerIpv4PeerPool, PppoxServerIpv6PeerPool, TrillIf, VbrasIf, VlanBlock, VlanIf, VxlanGpeIf, VxlanIf
|
Specifies network endpoint stacking.
|
TopLevelIfSource (TopLevelIf) |
EmulatedDevice, ExternalDevice, ExternalDevicePort, Host, Port, Router, SUT
|
Specifies the top-level interface in the interface stack.
|
L2tpv2UdpConfig (UdpSrcCustomIf) |
L2tpv2BlockConfig
|
Config to Udp source custom interface.
|
UnicastExpectedRxPorts (UnicastExpectedRxPorts) |
Port
|
Traffic sent to this end point is expected to be received as unicast traffic by any
of the ports connected through this relation.
|
UsesIfSource (UsesIf) |
AncpAccessNodeConfig, AppPerfClientConfig, AppPerfServerConfig, AutosarTimeSyncConfig, BfdRouterConfig, BridgePortConfig, CifsClientProtocolConfig, CifsServerProtocolConfig, CoapServerConfig, CuspProtocolConfig, Dhcpv4BlockConfig, Dhcpv4ServerConfig, Dhcpv6BlockConfig, Dhcpv6PdBlockConfig, Dhcpv6ServerConfig, Dot1xSupplicantBlockConfig, DpgClientProtocolConfig, DpgServerProtocolConfig, DualStackLiteConfig, EcpriProtocolConfig, EoamNodeConfig, FcEPortConfig, FcFPortConfig, FcHostConfig, FcoeHostConfig, FcoeVePortConfig, FcoeVfPortConfig, FtpClientProtocolConfig, FtpServerProtocolConfig, HttpClientProtocolConfig, HttpServerProtocolConfig, Ieee1588v2ClockConfig, Ieee80211AccessPointConfig, Ieee80211ClientConfig, Ieee8021asClockConfig, IgmpHostConfig, IgmpRouterConfig, IperfClientProtocolConfig, IperfServerProtocolConfig, Ipv6RapidDeploymentConfig, L2tpv2BlockConfig, L2tpv3BlockConfig, LacpPortConfig, LagBfdPortConfig, LinkOamRouterConfig, LispRouterConfig, LldpNodeConfig, LspPingProtocolConfig, MacsecSupplicantBlockConfig, MldHostConfig, MldRouterConfig, MplsTpConfig, MplsTpOamNodeConfig, MsdpProtocolConfig, NetconfClientConfig, NetconfProtocolConfig, NtpClientConfig, OamFlexeClientConfig, OpenflowControllerProtocolConfig, OpflexDeviceConfig, OseSwitchConfig, Ospfv2RouterConfig, Ospfv3RouterConfig, OtvEdgeDeviceConfig, OtvSiteDeviceConfig, OvsdbServerConfig, PacketChannel, PcepProtocolConfig, PimRouterConfig, PppoaClientBlockConfig, PppoaServerBlockConfig, PppoeClientBlockConfig, PppoeServerBlockConfig, PppoL2tpv2ClientBlockConfig, PppoL2tpv2ServerBlockConfig, PppoL2tpv3ClientBlockConfig, PppoL2tpv3ServerBlockConfig, PppProtocolConfig, RawTcpClientProtocolConfig, RawTcpServerProtocolConfig, RipRouterConfig, RoEBlockConfig, SaaDeviceConfig, SipUaProtocolConfig, SrpConfig, Srv6OamProtocolConfig, StorageWorkerConfig, SyncEthDeviceConfig, TrillRbridgeConfig, TwampClientConfig, TwampServerConfig, VdpStationConfig, VicAdapterConfig, VideoClientProtocolConfig, VideoServerProtocolConfig, VifConfig, VsiBlockConfig, VxlanVtepConfig, XmppvJClientConfig
|
Specifies the interfaces used by the configuration object (configuration object
examples: BgpRouterConfig, LdpRouterConfig, and so on).
|
Attribute |
Description |
Common Writable Attributes
|
Active, Name
|
Cfi
|
VLAN CFI.
Type: u8
Default: 0
Range: 0 - 1
|
IdList
|
A Tcl list of VLAN IDs. To use this attribute, the IsRange attribute must
be FALSE.
Type: u16
Default: 0
|
IdRepeatCount
|
How many times to repeat the same VLAN ID before incrementing it. See
VlanId for more information.
Type: u16
Default: 0
|
IdResolver
|
Id resolver.
Type: string
Default: default
|
IdStep
|
VLAN ID step value. See VlanId for more information.
Type: s16
Default: 1
|
IfCountPerLowerIf
|
Number of interfaces in this interface object.
Type: u32
Default: 1
|
IfRecycleCount
|
How many times to increment the VLAN ID before returning to the starting
value. See VlanId for more information.
Type: u32
Default: 0
|
IsLoopbackIf
|
Whether this is a loopback interface.
Type: bool
Default: FALSE
Possible Values:
Value |
Description |
TRUE |
This is a loopback interface.
|
FALSE |
This is not a loopback interface.
|
|
IsRange
|
Whether to use a combination of attributes to generate a range of VLAN IDs,
or to use the IdList attribute to specify the VLAN IDs.
Type: bool
Default: TRUE
Possible Values:
Value |
Description |
TRUE |
Use a combination of attributes to generate a range of VLAN IDs.
The attributes are VlanId, IdStep, IdRepeatCount, and IfRecycleCount. See
VlanId for more information.
|
FALSE |
Use the IdList attribute to specify the VLAN IDs.
|
|
Priority
|
VLAN priority.
Type: u8
Default: 7
Range: 0 - 7
|
Tpid
|
Tpid.
Type: u16
Default: 33024
|
VlanId
|
VLAN ID. You can generate more than one VLAN ID by using IdRepeatCount,
IdStep, and IfRecycleCount. If you do that, then the value of this attribute is the
starting VLAN ID.
To use this attribute, the IsRange attribute must be TRUE.
Example: VlanId = 1, IdStep = 1, IfRecycleCount = 2, IdRepeatCount = 0.
Generated values will be 1, 2, 1, 2, 1, 2, and so on.
Example: VlanId = 1, IdStep = 1, IfRecycleCount = 2, IdRepeatCount = 1.
Generated values will be 1, 1, 2, 2, 1, 1, 2, 2, 1, 1, 2, 2, and so
on.
Type: u16
Default: 100
Range: 0 - 4095
|